![\"clip_image001\"](\"http:\/\/lh5.ggpht.com\/-jJT7v8mP5IQ\/VN5cAWgdN_I\/AAAAAAAAIn0\/sXiUbygWZZQ\/s1600-h\/clip_image0013.jpg\" "\\"clip_image001\\"")
<\/a><\/p>\nFigure below shows the system circuit suction line filter system, where the filter is installed after the tank and before the pump, the fluid system will be sucked by the pump must first be through the filter, so the filter will protect the pump against fluid particles to enter. The disadvantage of this system is:<\/p>\n
- \n
- Filters are not easily taken, because the built-in reservoir.<\/span><\/span><\/li>\n
- There was a decrease sufficiently high pressure and cavitation arise.<\/span><\/span><\/li>\n
- Expensive<\/span><\/span><\/li>\n<\/ul>\n
\u00a0<\/div>\nIn the hydraulic system, the pump is working to create a fluid flow (to move the fluid volume) and provides the force needed. Siphon pump fluid (usually from the tank) and subjecting it to the exit (outlet). From there the fluid entering the system and reach the actuator \/ user (in the form of a piston mi) by using a separate control element. Users will give custody to the fluid, for example the piston of the cylinder step will accept loads. Because of this talianan, an increase in fluid pressure to a high enough to overcome the forces of prisoners. Pressure in the hydraulic system is not created by the hydraulic pump, nanium happen by itself kanena their prisoners opposite to the direction of flow. High press the fluid can also be seen as a connecting rod pump fluid which provides the necessary force.
\u00a0
Gear pump<\/strong>
Gear pumps are fixed displacement pump types. Gear pumps can be divided:
(1) gear pump with gears inside
(2) poinpa gear with external gear
\u00a0
Gear pump with gears inside.<\/strong>
The main part is a numah (1) where there is a pair of gears that move (such that the loose in the axial and radial direction so that the unit is practically submerged oil. Part sucking (white triangles) is connected to the tank, a pressure part (black triangles) associated with hydraulic system. The gears in (2), moving in the direction of the arrow and move the gear outside (3) in the same direction. This round lead separate gears so that the cavity-free teeth into.<\/div>\n\u00a0<\/div>\nResulting in a negative pressure on the fluid in the tank while the pump has atmospheric pressure, so that the fluid flow from the tank to the pump. This process is commonly called a “suction pump”. Fluid fills spaces gears, thus forming a closed space with a home and a crescent shaped element 4 during the next movement in the push to the press (triangle black) gears and meeting each other again and encourage fluid and spaces gears. Both gears are touching each other to prevent reversal of flow of press roared into the suction chamber.<\/div>\n\u00a0<\/span><\/span>![\"clip_image002\"](\"http:\/\/lh5.ggpht.com\/-xeAXBlSU_YE\/VN5cF4Irs5I\/AAAAAAAAIpM\/XKEhnREU6Z8\/clip_image002_thumb.jpg?imgmax=800\" "\\"clip_image002\\"")
<\/a><\/div>\nFigure 4.64 gear pump in
\u00a0
Gear pump with external gears<\/strong>
In this case the two outer gear wheels will contact each other. 2 driven gears corresponding arrows and cause the gears 3 moves opposite. Imbibing the same process occurs with this type of gear pump as described in the preceding. Fluid in space gear 4 pushed out and out of the slit on the side gears press. From the picture pieces can easily be seen gears close the gap before the passage celah- really empty. Without reducing the burden on the remaining spaces. very high pressures can occur that will cause severe vibration in the pump. To the burden placed on a deduction hole is located on the side bearing blocks. Due to high pressure, then formed then the incompressible fluid into the press room. Note that is considered important is tolerance side clearances between gears 5 and 6 bearing block.<\/div>\n\u00a0<\/span><\/span>![\"clip_image003\"](\"http:\/\/lh4.ggpht.com\/-OBSL9xesnR4\/VN5cIlCX82I\/AAAAAAAAIp4\/fGPQ_UrHUc8\/clip_image003_thumb.jpg?imgmax=800\" "\\"clip_image003\\"")
<\/a><\/div>\n - There was a decrease sufficiently high pressure and cavitation arise.<\/span><\/span><\/li>\n