The practice of using a combustion furnace with gas fuel is felt relatlf Iebih cheap and easy compared to other furnaces.<\/span> By using the gas furnace combustion neutral conditions, oxidation or reduction can be easily achieved, by setting the gas, primary air duct and damper.<\/span>
\n<\/a>
\n Figure 40. Furnace gas.<\/span><\/p>\n

Some things to consider in implementing the practice of burning the gas furnace is:<\/span><\/p>\n

\n
• At the beginning of the combustion process, the furnace door in the open position of approximately 12 mm, and recently closed when the temperature had reached 200 ^{o<\/sup> C.<\/span><\/li>\n}
• A damper in the fully open position<\/span><\/li>\n
• Primary air channel in the closed position, and opened after the temperature reaches 580 ^{o<\/sup> C-620 o<\/sup> C.<\/span><\/li>\n}
• Use stakes seger in accordance with the desired fuel temperature.<\/span> Control the temperature rise every 15-20 minutes.<\/span><\/li>\n<\/ul>\n

  Process gas furnace operation<\/strong><\/span>
  \n a. Preparation<\/strong><\/span>
  \n 1).<\/span> Gas furnace<\/span>
  \n 2).<\/span> Thermocouple-pyrometer, and pyrometric cone (stake)<\/span>
  \n 3).<\/span> Kiln furniture: plate, prop (pillar)<\/span><\/p>\n

  b. Preparation<\/strong><\/span>
  \n 1).<\/span> Replace the plate in the bottom of the furnace with a given buffer.<\/span>
  \n 2).<\/span> Stacking ceramic objects on the plate until it is full.<\/span> Place pancanq \/ cone temperature to determine the temperature of combustion at every level.<\/span>
  \n<\/a><\/p>\n

  c. Burning<\/strong><\/span>
  \n 1) Play \/ open fully valves on the gas cylinder.<\/span>
  \n 2) Open the regulator on the gas pipeline with position 4 kPa.<\/span> Remember the main gas line and the pilot flame flame on the burner in the low position and the position of the fire button is pressed.<\/span>
  \n 3) Turn on the burner and set fire to the magnitude of the flame by turning the main flame until achieving the temperature of 160 ^{o<\/sup> C- 180 0<\/sup> C in less than 1 hour.<\/span>
  \n}<\/a>
  \n 4) Close the damper to the remaining hole 7.5 cm.<\/span>
  \n 5) If the above mentioned temperature has been reached, turn the flame up around the fire grew and the temperature increased to 210 ^{\u00b0<\/sup> C-230 \u00b0<\/sup> C within 1 \u00bd hours, then turn the pilot flame in a high position.<\/span>
  \n 6) Add gas through the main flame until the pyrometer temperature reached 420 \u00b0<\/sup> C- 460 0<\/sup> C within 2 1\/2 hours.<\/span> Add gas after achieving the temperature of 580 0<\/sup> C-620 0<\/sup> C within 3.5 hours.<\/span>
  \n 7) Open the primary air channel in full and open the damper to 11.5 cm.<\/span>
  \n}<\/a>
  \n 8) If the temperature has been reached in accordance with Seger stake or pyrometer, the temperature needs to arrest about 15 minutes later a fire at the burner can be turned off by turning the regulator on the gas cylinder.<\/span>
  \n 9) Close all gas lines and return it to its original position, then close the damper, as well as the primary air duct burner holes to keep the heat in the furnace chamber does not quickly disappear<\/span>
  \n 10) Cool the furnace with the same time as the length of time the combustion process.<\/span> Furnaces should be opened apablia temperature has been below 200 ^{o<\/sup> C.<\/span><\/p>\n","protected":false},"excerpt":{"rendered":"}

  The practice of using a combustion furnace with gas fuel is felt relatlf Iebih cheap and easy compared to other furnaces. By using the gas furnace combustion neutral conditions, oxidation or reduction can be easily achieved, by setting the gas, primary air duct and damper. Figure 40. Furnace gas. Some things to consider in implementing …<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1812],"tags":[1659,1661,1667,1668,1665,1660,1662,1663,1666,1664],"class_list":["post-1169","post","type-post","status-publish","format-standard","hentry","category-english","tag-furnace-gas","tag-furnace-gas-leak","tag-furnace-gas-line","tag-furnace-gas-regulator","tag-furnace-gas-smell","tag-furnace-gas-valve","tag-furnace-gas-valve-not-opening","tag-furnace-gas-valve-price","tag-furnace-gas-valve-wiring","tag-furnace-gasket"],"_links":{"self":[{"href":"https:\/\/www.tneutron.net\/seni\/wp-json\/wp\/v2\/posts\/1169","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.tneutron.net\/seni\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.tneutron.net\/seni\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.tneutron.net\/seni\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.tneutron.net\/seni\/wp-json\/wp\/v2\/comments?post=1169"}],"version-history":[{"count":1,"href":"https:\/\/www.tneutron.net\/seni\/wp-json\/wp\/v2\/posts\/1169\/revisions"}],"predecessor-version":[{"id":3358,"href":"https:\/\/www.tneutron.net\/seni\/wp-json\/wp\/v2\/posts\/1169\/revisions\/3358"}],"wp:attachment":[{"href":"https:\/\/www.tneutron.net\/seni\/wp-json\/wp\/v2\/media?parent=1169"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.tneutron.net\/seni\/wp-json\/wp\/v2\/categories?post=1169"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.tneutron.net\/seni\/wp-json\/wp\/v2\/tags?post=1169"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}