Rotating equipment (rotating equipment), equipment used to provide round the circuit drilling.<\/span> Round produced has enormous power to be able to play a long series of drilling.<\/span> Some functions of rotating equipment (rotating equipment), among others:<\/span>
\n – Rotate the drill rod during drilling operations.<\/span>
\n – Holding and hanging drill rod or other pipes with slip-slip or disconnect the tube from the circuit piping rotary drill (rotary slip) while adding or removing the drill pipe from the pipe circuit.<\/span><\/p>\n

Rotating equipment consists of: Rotary table, Master Bushing, Kelly bushing, Rotary slips, Insert bowl \/ bowl slip, Make up and break out the barrel, Kelly spinner.<\/span>
\n a. Tables Turn,<\/strong> mounted above the drill floor where there is a master bushing.<\/span> In the box there is a master bushing is entered by the pin of the kelly bushing.<\/span> So that when the rotary table rotates, spinning master bushing and kelly bushing will rotate.<\/span> Overview rotary table, can be seen in Figure 4.12.<\/span>
\n<\/a>
\n Figure 4.12.<\/span> Rotary Table<\/span><\/p>\n

The tool is mounted on the drill floor and perpendicular to the traveling block.<\/span> The middle of the rotary table there is a hole, and master bushing mounted in it.<\/span> Rotary table must be cleaned of mud scattered, so that operators do not slip on the drill floor when working on the drill floor.<\/span> The cleaning is done with water spray.<\/span> Size and rotary table load capacity ranges from 100 to 600 tons.<\/span><\/p>\n

Drilling rotation speed ranging from 35 to 200 rounds per minute clockwise.<\/span> Speed \u200b\u200bis regulated by Driller, depending on the type of drill bit used and layers penetrated.<\/span> Power distribution system to the turntable in two ways:<\/span>
\n – Through the chain drive to “Drawwork”, table-driven player with a chain transmission system, which is driven by the gear teeth (sprockets) in drawwork.<\/span> Can be seen in Figure 4.13.<\/span>
\n<\/a>
\n Figure 4.13.<\/span> Rotary table with driving Drawwork<\/span><\/p>\n

– Direct relationship with prime movers (prime mover of independent drives).<\/span><\/p>\n

b.<\/span> Top Bearing is a tool that can dilepasdan replaced with properly sized holes on the table and the players operating requirements.<\/span> This instrument became the seat of one of the two scientific equipment that players rotary kelly bushing or slip.<\/span> Kelly kelly inserted through bearings, main bearings and turntable.<\/span> Then the power swivel (rotating movement) forwarded from the player to the table kelly and drill rod underneath.<\/span><\/p>\n

If a player slips inserted into the main bearing, will be used to hang the drill rod at the time of addition or subtraction sections of drill rod.<\/span> Can withstand because they have sharp teeth and a tapered shape (dies).<\/span> Rotary slips inserted into the main bearings around the drill rod so that the drill rod hangs freely in the wellbore.<\/span> There are two basic types of master bushing (main bearing), namely: the type of intact (solid) and type two parts or type split (split).<\/span>
\n<\/a>
\n Figure 4.15.<\/span> Master Bushing type of solid<\/span><\/p>\n

c. Kelly bushing<\/strong> is a tool that is installed into the master bushing to channel the style of play on kelly and drill stem wellbore while drilling (holes).<\/span> The hole on the kelly bushing is shaped the same as the form used kelly square, triangles or hexagons.<\/span> There are two basic types of bearings kelly:<\/span>
\n – Pin Drive: Has four pins inserted into the upper part of the master bushing.<\/span>
\n – Square Drive: Having a single drive quadrangular inserted into the master bushing.<\/span>
\n<\/a>
\n Figure 4.17.<\/span> Pin Drive (left) and Square Drive (right)<\/span><\/p>\n

d. Rotary slip<\/strong> is a tool for hanging a series of drilling on the rotary table when Kelly released, to add a new drillpipe.<\/span> Rotary slip also be used to hang a series of drilling on the rotary table in the circuit when removing the drilling of holes.<\/span> Rotary slip hold joint drill pipe tool while hanging on the rotary table.<\/span> Dies of rotary slip biting drill pipe tool joint.<\/span> Before use of rotary dies hose should be cleaned from sand, and checked his condition.<\/span>
\n<\/a>
\n Figure 4.18.<\/span> Rotary Slip<\/span><\/p>\n

e. Slip Bowl<\/strong> is bearing filler metal that sits in the master bushing to set or adjust the size of the pipe and slip used that vary according to the needs.<\/span>
\n<\/a>
\n Figure 4.19.<\/span> slip Bowl<\/span><\/p>\n

f. Safety clamp<\/strong> used while holding the drill collar, where the drill collar that did not have a tool joint.<\/span> To hold \/ hang up drill collars, rotary slip should be provided with safety clamp mounted on it.<\/span>
\n<\/a>
\n Figure 4.20.<\/span> safety Clamp<\/span><\/p>\n

g. Rotary barrel<\/strong> is large keys that hung above the rig floor near the turntable, which is mounted on portions of the drill rod, both to connect and disconnect.<\/span> The key is to break out cans or kegs lead and make up or back up tong tong.<\/span>
\n<\/a>
\n Figure 4.21.<\/span> Rotay Tong<\/span><\/p>\n

h. Kelly spinner<\/strong> mounted on the bottom of the swivel stem.<\/span> This tool is used to connect kelly with drill pipe rapidly in the rat hole (hole a place to store and install or dismantle a series of pipes).<\/span>
\n<\/a>
\n Figure 4.22.<\/span> Kelly Spinner<\/span><\/p>\n

Top drive drilling system<\/strong> is a<\/strong> system with a rotating drill stem drilling using a player that is mounted directly below the swivel and the player moves up and down following the movements of traveling block.<\/span> With this system, and kelly kelly bushing is not needed because the drill stem is rotated directly by the motor drilling assembly suspended from the traveling block.<\/span> Construction of top drive consists of:<\/span>
\n a.<\/span> standard rotary swivel<\/span>
\n b.<\/span> Drilling motors assembly<\/span>
\n c.<\/span> Guide dolly system assembly<\/span>
\n d.<\/span> Pipe handler assembly<\/span>
\n<\/a>
\n Figure 4.23.<\/span> Top Drive<\/span><\/p>\n","protected":false},"excerpt":{"rendered":"

Rotating equipment (rotating equipment), equipment used to provide round the circuit drilling. Round produced has enormous power to be able to play a long series of drilling. Some functions of rotating equipment (rotating equipment), among others: – Rotate the drill rod during drilling operations. – Holding and hanging drill rod or other pipes with slip-slip …<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1865],"tags":[1738,1740,1736,1739,1737,1731,1735,1732,1733,1734],"class_list":["post-1193","post","type-post","status-publish","format-standard","hentry","category-english","tag-drilling-equipment-crossword","tag-drilling-equipment-crossword-clue","tag-drilling-equipment-for-sale","tag-drilling-equipment-manufacturers","tag-drilling-equipment-pdf","tag-equipment-drilling","tag-equipment-drilling-oil","tag-equipment-drilling-rig","tag-equipment-drilling-rigs-sale","tag-equipment-drilling-water-well"],"_links":{"self":[{"href":"https:\/\/www.tneutron.net\/sipil\/wp-json\/wp\/v2\/posts\/1193","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.tneutron.net\/sipil\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.tneutron.net\/sipil\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.tneutron.net\/sipil\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.tneutron.net\/sipil\/wp-json\/wp\/v2\/comments?post=1193"}],"version-history":[{"count":1,"href":"https:\/\/www.tneutron.net\/sipil\/wp-json\/wp\/v2\/posts\/1193\/revisions"}],"predecessor-version":[{"id":3442,"href":"https:\/\/www.tneutron.net\/sipil\/wp-json\/wp\/v2\/posts\/1193\/revisions\/3442"}],"wp:attachment":[{"href":"https:\/\/www.tneutron.net\/sipil\/wp-json\/wp\/v2\/media?parent=1193"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.tneutron.net\/sipil\/wp-json\/wp\/v2\/categories?post=1193"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.tneutron.net\/sipil\/wp-json\/wp\/v2\/tags?post=1193"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}